Avaya 6101.1 Exam Syllabus Topics:
| Section | Objectives |
|---|---|
| Layer 2 Switching | - Spanning Tree Protocol (STP/RSTP/MSTP) - VLAN configuration and tagging - Link Aggregation (LACP, SMLT, RSMLT) |
| Quality of Service (QoS) | - Traffic classification and prioritization - Queue management and bandwidth control |
| Ethernet Routing Switch Fundamentals | - Switch operation and forwarding behavior - Hardware components and ERS architecture |
| Layer 3 Routing on ERS | - Inter-VLAN routing - RSMLT and redundancy mechanisms - Static routing and routing concepts |
| Security and Management | - Authentication and access control - Device monitoring and troubleshooting |
Avaya Ethernet Routing Switch Implementation Sample Questions:
Question 1
During a power-on or cold-start sequence, at which stage can he flags to change the operational environment of the switch be set?
A. boot monitor prompt
B. boot configuration prompt
C. image search
D. PC system test
Question 2
A network has some Ethernet Routing Switch (ERS) 5500 switches licensed at the advanced level for Release 6 2 A technician implementing Protocol independent Multicast
-
Sparse Mode (PIM-SM) Which licensing requirement applies?
A. the PIM-SM is included m the base license with release 6.2
B. A Premier license is needed
C. the PIM-SM con only be licensed on ERS 5510 models
D. the PIM-SM is already covered by the existing advanced feature license
Question 3
The User interface (Ul) button on the Ethernet Routing Switch (ERS) 6500 can be used to temporarily reset a switch to the default IP address.
Which two statements are true about the default IP address set via the Ul button? (Choose two)
A. the default IP address changes if there is a change in the state of the switch, such as if the switch joins or leaves a stack.
B. the default IP address is saved in NVRAM across resets of the switch/stack.
C. The default IP address overwrites the "configured" IP address settings that are set via console. CLI or Web.
D. The default IP address overrides the IP address currently in use by the switch stack.
Question 4
When multiple VLANs are used, DHCP relay is required to get the DHCP information from the end user VLAN to the DHCP server (which would normally sit on core server VLAN)
Which statement about how to enable DHCP relay for a VLAN Is true?
A. The virtual VLAN IP address is used as the DHCP relay agent
B. The physical VLAN IP address is used as the DHCP relay agent
C. the IP address of the DHCP relay agent is used
D. the IP address of the core server VLAN is used.
Question 5
A technician has implemented RSMLT edge design. After recovering from power outage some clients could not communicate. It has been stated that only one of the core RSMLT switches has recovered.
What should have been done to prevent the loss of communications?
A. Set the VLAN to copy RSMLT into from a similarity configured VLAN.
B. Increase the hold up timer to 9999.
C. Clear the peer IP and MAC addresses.
D. Turn off the hold down timer.
Solutions:
| Question 1 Answer: A | Question 2 Answer: A | Question 3 Answer: C,D | Question 4 Answer: A | Question 5 Answer: D |
1179 Customer Reviews
Quality and ValueITCertKing Practice Exams are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development - no all study materials.
Tested and ApprovedWe are committed to the process of vendor and third party approvals. We believe professionals and executives alike deserve the confidence of quality coverage these authorizations provide.
Easy to PassIf you prepare for the exams using our ITCertKing testing engine, It is easy to succeed for all certifications in the first attempt. You don't have to deal with all dumps or any free torrent / rapidshare all stuff.
Try Before BuyITCertKing offers free demo of each product. You can check out the interface, question quality and usability of our practice exams before you decide to buy.
